|
Thông tin chi tiết sản phẩm:
|
Chứng nhận: | CE | Điều kiện: | Mới |
---|---|---|---|
Bước sóng làm việc:: | 10,6um | Quyền lực: | 60W / 80W 150W |
Từ khóa: | Cửa sổ bảo vệ laze | Quility: | Trình độ cao |
Đường kính: | 60mm | Từ khóa: | Ống laser |
Loại laser: | Máy cắt laser Co2 | Chiều dài: | 160mm |
Điểm nổi bật: | Máy cắt laser |
60w / 80w / 100w / 130w / 150w / 180w Ống cắt laser Laser Co2 cho máy cắt laser Co2
Sự chỉ rõ:
Mô hình | Công suất định mức (W) | Công suất tối đa (w) | Chiều dài (mm) | Đường kính (mm) | Xúc tác |
JSD-50-700 | 40 | 50 | 700 | 50 | Đúng |
JSD-50-800 | 50 | 60 | 800 | 50 | Đúng |
JSD-50-1000 | 50 | 70 | 1000 | 50 | Đúng |
JSD-55-1000 | 50 | 70 | 1000 | 55 | Đúng |
JSD-55-1200 | 60 | 80 | 1200 | 55 | Đúng |
JSD-55-1250 | 60 | 80 | 1250 | 55 | Đúng |
JSD-60-1200 | 60 | 80 | 1200 | 60 | Đúng |
JSD-60-1250 | 60 | 80 | 1250 | 60 | Đúng |
JSD-80-1250 | 80 | 100 | 1250 | 80 | Đúng |
JSD-60-1600 | 80 | 110 | 1600 | 60 | Đúng |
JSD-80-1200 | 90 | 100 | 1200 | 80 | Đúng |
JSD-80-1400 | 100 | 120 | 1400 | 80 | Đúng |
JSD-80-1450 | 100 | 120 | 1450 | 80 | Đúng |
JSD-80-1600 | 130 | 150 | 1600 | 80 | Đúng |
JSD-80-1650 | 130 | 160 | 1650 | 80 | Đúng |
JSD-80-1800 | 150 | 180 | 1800 | 80 | Đúng |
JSD-80-2000 | 180 | 190 | 2000 | 80 | Đúng |
1, first line the electrode, (+, -) is not wrong. 1, dòng đầu tiên điện cực, (+, -) không sai. CO2 laser (laser tube) installation instructions: Hướng dẫn lắp đặt laser CO2 (ống laser):
2, installation of cooling water pipe, the installation method of water from the negative electrode, the positive water and meet the principle of falling out, and the interface can not leak. 2, lắp đặt ống nước làm mát, phương pháp lắp đặt nước từ điện cực âm, nước dương và đáp ứng nguyên tắc rơi ra, và giao diện không thể rò rỉ. Sufficient water must be stored in the pre - storage water storage device. Đủ nước phải được lưu trữ trong thiết bị lưu trữ nước trước khi lưu trữ. After water, the water cooling pipe must be used without air bubbles (must be viewed before each use). Sau nước, ống làm mát nước phải được sử dụng mà không có bọt khí (phải được xem trước mỗi lần sử dụng). If the laser tube is vertically installed, please notice that there is no bubble at the top of the laser tube. Nếu ống laser được lắp đặt theo chiều dọc, xin lưu ý rằng không có bong bóng ở đầu ống laser. When the bubble exists, it will cause damage to the laser tube if it runs. Khi bong bóng tồn tại, nó sẽ gây ra thiệt hại cho ống laser nếu nó chạy.
3, in order to maintain the good performance of the laser tube, please use a temperature controlled water cooler between 20-25 degrees Celsius. 3, để duy trì hiệu suất tốt của ống laser, vui lòng sử dụng bộ làm mát nước được kiểm soát nhiệt độ trong khoảng 20-25 độ C. If the cooling water is unstable, the output power of the laser tube will be unstable. Nếu nước làm mát không ổn định, công suất đầu ra của ống laser sẽ không ổn định.
4, when the laser tube is installed, there is enough space between the high pressure end of the laser tube and any other metal surface. 4, khi lắp đặt ống laser, có đủ khoảng trống giữa đầu áp suất cao của ống laser và bất kỳ bề mặt kim loại nào khác. If the gap is too small, triggering the high pressure of the laser tube will cause fire to the metal surface, which will cause damage to the laser tube and even cause damage to other main components of the laser. Nếu khe hở quá nhỏ, việc kích hoạt áp suất cao của ống laser sẽ gây cháy cho bề mặt kim loại, điều này sẽ làm hỏng ống laser và thậm chí gây hư hại cho các thành phần chính khác của laser.
5, it is suggested that an automatic inspection device be added to the cooling water circulation system of the laser tube, so as to prevent the laser tube from overheating due to the water failure. 5, đề nghị nên thêm một thiết bị kiểm tra tự động vào hệ thống tuần hoàn nước làm mát của ống laser, để tránh ống laser bị quá nóng do hỏng nước. For details, consult the supplier of the laser machine. Để biết chi tiết, tham khảo nhà cung cấp của máy laser.
Người liên hệ: Coco
Tel: +86 13377773809